Austweld
Refine Search
- Digital LED easily read in dark places
- Accuracy set the conditions by Dial
- Low energy consumption
- High-efficiency feeder and torch enhancing weldability
- Excellent function enhancing the economy and operation
- Digital LED easily read in dark places
- Accuracy set the conditions by Dial
- Low energy consumption
- High-efficiency feeder and torch enhancing weldability
- Excellent function enhancing the economy and operation
- Digital Display parameters
- Excellent welding characteristics in MMA with any kind of electrodes, including cellulosic, and in TIG with “lift arc” striking
- Low energy consumption
- High reliability when used with generator sets
- Suitable to be used with mains cable lengths over 100m
- Automatic compensation for mains voltage fluctuations within ±20%
- Digital Ammeter with welding current presetting and Hold Function of the last read value
- Reduced weight and size, easy-to-carry
- Innovative and compact design
- IP23 protection class and “Tunnel” fan cooling system allow operation in the toughest work environments
- Adjustable HOT START to improve arc striking with the most difficult electrodes
- Adjustable WIDTH CURRENT to choose the best arc dynamic characteristics
- OPTIONAL-STAND BY function on the remote control
- Digital LED easily read in a dark place
- Accuracy set the conditions by Dial
- Low energy consumption
- High-efficiency feeder and torch enhancing weldability
- Excellent function enhancing the economy and operation
- Digital LED easily read in dark places
- Accuracy set the conditions by Dial
- Low energy consumption
- High-efficiency feeder and torch enhancing weldability
- Excellent function enhancing the economy and operation
- Innovative and user-friendly design
- Low energy consumption
- High efficiency feeder and torch enhancing weld ability
- Excellent function enhancing the economy and operation
- IP21S protection class and dust-proof electronic components, fan cooling system, allows use in the toughest work environment
- Wire spool lodging up to 300mmØmax
- Digital LED easily read in dark places
- Accuracy set the conditions by Dial
- Low energy consumption
- High-efficiency feeder and torch enhancing weldability
- Excellent function enhancing the economy and operation
- Smart design with built-in an innovative, ergonomic chassis standard equipment panel
- Multifunction power source with optimal welding characteristics in MIG-MAG, MMA & TIG
- Built-in polarity changeover facility for most common gas & gasless wires
- Central Euro connection for the torch
- Low spatter maximum spatter reduction for the whole current range reduction of the spatter up to 80%
- IP21S protection class and dust-proof electronic components, fan cooling system, allows use in the toughest work environment
- Wire spool lodging up to 305mmØ
- Smart design with built-in an innovative, ergonomic chassis standard equipment panel
- Multifunction power source with optimal welding characteristics in MIG-MAG, MMA & TIG
- Built-in polarity changeover facility for most common gas & gasless wires
- Central Euro connection for the torch
- Low spatter maximum spatter reduction for the whole current range reduction of the spatter up to 80%
- IP21S protection class and dust-proof electronic components, fan cooling system, allows use in the toughest work environment
- Wire spool lodging up to 305mmØ
- The narrow plasma arc produces a sharp edge, free of distortion
- The stable plasma arc provides quality cuts comparable to oxy-fuel cutting – even with intermediate gauge plate and with minimum dross
- Plasma cutting is 4 times faster as compared to gas cutting
- High speed and low-cost cutting
- The surface finish resembles that produced by gas cutting
- Easy operation and high cutting capacity
- Air pressure manometer on the front panel
- Cutting, safety & protection cycles fully displayed by LEDs
- Automatic gas post flow for torch cooling
- The narrow plasma arc produces a sharp edge, free of distortion
- The stable plasma arc provides quality cuts comparable to oxy-fuel cutting – even with intermediate gauge plate and with minimum dross
- Plasma cutting is 4 times faster as compared to gas cutting
- High speed and low-cost cutting
- The surface finish resembles that produced by gas cutting
- Easy operation and high cutting capacity
- Air pressure manometer on the front panel
- Cutting, safety & protection cycles fully displayed by LEDs
- Automatic gas post flow for torch cooling
- Low energy & air consumption
- Safety protections on the torch to safeguard the operator
- PMW current mode control
- Post-gas can be adjustable
- Non- contact HF arc starting with pilot arc
- Smart design with built-in an innovative, ergonomic and robust chassis standard equipped panel
- The narrow plasma arc produces a sharp edge, free of distortion
- The stable plasma arc provides quality cuts comparable to oxy-fuel cutting – even with intermediate gauge plate and with minimum dross
- Plasma cutting is 4 times faster as compared to gas cutting
- High speed and low-cost cutting
- The surface finish resembles that produced by gas cutting
- Easy operation and high cutting capacity
- Air pressure manometer on the front panel
- Cutting, safety & protection cycles fully displayed by LEDs
- Automatic gas post flow for torch cooling
- AC/DC hybrid pulse TIG welding source the meaning of “highest quality” and “easiness of use” is redefined
- Smart design with full PWM current digital control
- STM 32MCU digital control full-bridge technology
- Improvement of the welding quality due to a variety of functions
- Improved welding of the thin sheet through “Silent PULSE” - function
- High concentrated welding arc improves the welding of butt-joint and cold arc - applications
- Multiprocessor AC TIG square wave (AC GTAW), DC TIG (DC GTAW), AC TIG Pulse square wave (AC GTAW-P), DC TIG Pulse (DC GTAW-P), DC Stick (DC SMAW)
- Welding parameters can be stored and invoked, use friendly
- Simple interface, easy to use, favorable man-machine conversation
- Multi waveform output includes AC square wave
- Zero crossing current control
- Minimum current for TIG is 5amps
- Foot pedal control can be available
- Overheating / over current protection
- Isolation circuit for TIG torch switch, reduce electromagnetic interference
- Low power consumption for energy saving
- Memorize and store 10 welding memory modes
- DC Pulse TIG
- Digital Lead easily read in dark places
- IP23 protection class and dust-proof electronic components.
- Precise and efficient Tig Arc striking by high frequency
- Automatic compensation for mains voltage within +15% -20%
- High performance on thin metal sheets
- Adopt soft contact functional keypress in the panel